Gutter replacement cost in Houston comes down to a few measurable things: how many linear feet of gutter the house needs, the metal you pick, how high the eaves are, how many downspouts the roof calls for, and whether the old gutters come off clean or expose rotted fascia. National cost guides put a typical whole-house job in the low-to-mid thousands of dollars. This Old House’s 2026 guide, based on Homewyse contractor estimates, gives $600 to $5,800 for a 2,000-square-foot home with about 200 linear feet of gutter, with an average of $3,200. Fixr reports a national range of $2,320 to $4,222 for a new installation and notes that replacing an existing system usually runs several hundred dollars more, because the old gutters have to come down first.
Those are national averages. Local labor rates, material prices and the condition of your roofline push them up or down. Where a Houston house lands in those ranges depends on its measured footage and the line items below, so the reliable number is a written quote for that house. The rest of this guide walks through each cost factor so you can read a quote line by line and tell whether two contractors are pricing the same job.
What drives gutter replacement cost in Houston
Linear feet
Gutters are priced by the running foot along the eaves, so footage is the starting point of every estimate. A contractor measures each run, then adds inside and outside corners, end caps and downspout outlets. A simple ranch house with long straight eaves costs less per foot than a house with lots of short runs, bump-outs and corners, because every corner and cap is another part and another joint to seal.
Material: aluminum, steel or copper
Aluminum gutter replacement is what most Houston homes get. Aluminum does not rust, it is light enough for long seamless runs, and it comes in a wide range of factory colors. Fixr lists national prices of $7 to $13 per linear foot for aluminum, $7 to $12 for steel and $18 to $32 for copper. Steel is heavier and resists dents from falling limbs, but once its coating is scratched it can rust, and our humidity does not help. Copper is mostly chosen for looks on historic or high-end homes.
Seamless vs. sectional
Sectional gutters come in pre-cut lengths that are joined with connectors and sealant. Seamless gutters are formed on site from a coil of metal, cut to the exact length of each run, so the only joints are at corners and outlets. Seams are where most gutter leaks start, which is why seamless costs more up front but tends to need less attention later. Bob Vila, citing HomeAdvisor data, puts labor at $2 to $6 per foot for sectional and $3 to $10 per foot for seamless.
5-inch vs. 6-inch gutters
Five-inch K-style is the standard residential size. Six-inch gutters hold more water and pair with larger downspouts, which matters on big or steep roof planes, on runs where a roof valley dumps water into one spot, and during the intense downpours Houston gets. A 6-inch system uses more metal, so it costs more per foot. If your roof is borderline, ask for both sizes priced side by side.
Stories, roof height and access
A second story means taller ladders, more setup time and longer downspouts. Bob Vila’s figures add about $1 to $3 per linear foot of labor for each additional story, and Fixr notes that a single-story home costs a few hundred dollars less than a two- or three-story home with the same design and material. Steep roof pitches, tight side yards, fences, pool enclosures and dense landscaping also slow the crew down.
Downspout count
Each downspout adds an outlet, elbows, straps and the pipe itself. Fixr lists downspout installation at $7.43 to $13.51 per linear foot nationally, so a two-story corner costs roughly twice as much as a one-story one. Adding a downspout is often the cheapest way to stop a long run from overflowing.
Removal and disposal of the old gutters
Taking down the old system is labor, and someone has to haul it away. Published figures vary: Bob Vila lists $0.65 to $0.85 per linear foot for removal and disposal, while Fixr lists $1.31 to $2.38 per linear foot for removal labor alone. Make sure removal and haul-off appear on the quote rather than as a surprise on the invoice.
Fascia repair found during removal
This is the line item that catches people off guard. When old gutters come down, the fascia board behind them is sometimes soft or rotted from years of overflow, and new gutters should not be screwed into bad wood. This Old House puts fascia replacement at $7 to $40 per linear foot for materials and labor, plus $3 to $7 per foot to remove the old board. A good quote spells out how fascia will be priced if it turns up, per foot or per board, before work starts.
Gutter screens and guards
Guards are optional, and national numbers for them are all over the place. Fixr describes adding guards to a full system as costing a few hundred dollars, while This Old House’s 2026 homeowner survey of name-brand systems found a median of $5,000. Basic screens sit at the low end and professionally installed micro-mesh at the high end. With oaks and pines dropping leaves, needles and pollen most of the year, many Houston homeowners add screens when the new gutters go up, which saves a separate trip.
National cost ranges at a glance
The table pulls the per-foot and per-project figures above into one place. Every number is a national average from a published cost guide, and the guides use different years and methods, so treat them as a reference point rather than a price for your house.
| Cost factor | National range | Source |
|---|---|---|
| Whole-house gutters, about 200 linear feet | $600 to $5,800 (average $3,200) | This Old House |
| New installation, whole home | $2,320 to $4,222 (average $3,223) | Fixr |
| Aluminum gutters | $7 to $13 per foot | Fixr |
| Steel gutters | $7 to $12 per foot | Fixr |
| Copper gutters | $18 to $32 per foot | Fixr |
| Labor, sectional vs. seamless | $2 to $6 vs. $3 to $10 per foot | Bob Vila |
| Each additional story | $1 to $3 more per foot in labor | Bob Vila |
| Downspouts, installed | $7.43 to $13.51 per foot | Fixr |
| Removing old gutters | $0.65 to $2.38 per foot | Bob Vila, Fixr |
| Fascia replacement, materials and labor | $7 to $40 per foot | This Old House |
How to compare gutter installation cost quotes
Two quotes for the same house can be far apart simply because they are not pricing the same work. Before you compare totals, line up the details:
- Footage and downspouts. Ask each contractor for the total linear feet and the number and size of downspouts. If one quote has noticeably fewer feet, find out why.
- The same spec. Material, metal thickness, 5-inch or 6-inch, seamless or sectional, and the type and spacing of hangers. Hidden hangers screwed into the rafter tails hold far better than old spike-and-ferrule hardware.
- Removal and haul-off. Confirm both are included.
- Fascia. Ask how rotted fascia will be handled and priced if it shows up.
- Drainage at the ground. Downspout extensions or splash blocks move water away from the slab, which matters on Houston’s expansive clay soils.
- Add-ons listed separately. Guards, extra downspouts and color upgrades should be their own lines so you can decide on each one.
- Warranty in writing. Ask what workmanship and material coverage each contractor offers and get it on paper.
The lowest number is not a bargain if it leaves out removal, skips the fascia question or uses thinner metal. The best value is the quote that is clear about what you are paying for.
Gutter repair and replacement in Houston: which costs less
A repair almost always costs less in the moment. Fixr’s national figures put gutter repair at $218 to $396, with an average around $307, against $2,582 to $4,699 for a full system replacement. If the gutters are basically sound, gutter repair is the sensible call:
- A few loose or failed hangers causing a sag
- One or two leaking seams or corners
- A dented section from a falling limb
- A downspout that has pulled loose or come apart
Replacement starts to make more financial sense when the problems are spread across the whole system: sectional seams leaking all along the house, gutters too small to keep up with a heavy storm, runs pitched the wrong way, rust-through on old steel, or fascia rot along much of the roofline that means the gutters have to come down anyway. At that point you are paying for repairs every season on a system that still underperforms. A gutter replacement with seamless aluminum, properly sized and pitched, resets the clock.
Frequently asked questions
Many single-family homes are a one-day job once the material is ready, because seamless gutters are formed on site from a coil machine. Larger homes, two-story houses, steep roofs and any fascia repairs found after the old gutters come down can stretch the job longer. Rain delays are common in Houston, so build in some flexibility when you schedule.
For most Houston homes, yes. Seams are the most common place for leaks to start, and a seamless run only has joints at corners and outlets. Aluminum does not rust in our humid climate and comes in many colors, so it is a good balance of price and service life compared with steel or copper.
Not always. Five-inch gutters handle most houses well. Six-inch makes sense on large or steep roof sections, under valleys that concentrate water into one spot, or where existing gutters overflow during heavy downpours even when clean. A contractor can look at the roof area draining to each run and tell you whether the larger size is worth it.
It depends on your policy and on the cause. Damage from a covered event, such as a storm or a falling tree, may be covered, while gutters that simply wore out usually are not. Take photos of the damage, call your insurer before work starts, and ask your contractor for an itemized estimate you can submit with the claim.
Get a quote
Arm Strong Gutters & Sheet Metal handles gutter repair and replacement for homes and businesses across Houston and Harris County, with footage, materials and removal spelled out on the estimate. Call 832-605-3397 or request a quote online and we will schedule a time to measure your house.